注意:因业务调整,暂不接受个人委托测试望见谅。
台灯, 吊灯, 壁灯, 床头灯, 地灯, 射灯,筒灯, 陶瓷灯, 轨道灯, 落地灯, 透明灯, 浴室灯, 烛台, 花灯, 摄影灯, 投影灯, 智能灯, LED灯, 纱灯, 山东灯
Visual Inspection Method: This method involves a visual examination of the lighting fixture. Inspect for any physical damage, such as cracks, dents, or loose parts.
Electrical Test Method: Use a multimeter to measure the electrical properties of the lighting fixture. Check for proper voltage, continuity, and resistance. Ensure that all connections are secure.
Light Output Measurement Method: Use a light meter to measure the luminous intensity or luminous flux of the lighting fixture. Compare the measurement to the manufacturer's specifications to determine if the light output is within the acceptable range.
Color Temperature Measurement Method: Use a color temperature meter to measure the color temperature of the lighting fixture. Compare the measurement to the desired color temperature to ensure it matches the intended lighting requirements.
Power Consumption Measurement Method: Use a wattmeter to measure the power consumption of the lighting fixture. Verify that the fixture is operating within the specified power limits to avoid energy waste or overloading the electrical system.
Heat Dissipation Test Method: Monitor the temperature of the lighting fixture during operation using a thermometer or thermal camera. Ensure that the heat dissipation is within safe limits to prevent overheating and potential fire hazards.
Insulation Resistance Test Method: Perform an insulation resistance test using a Megohmmeter. This test verifies the electrical insulation integrity of the lighting fixture. Ensure that the insulation resistance meets the required safety standards.
Waterproof Test Method: Subject the lighting fixture to a water immersion test or water spray test to determine its degree of waterproof performance. Inspect for any water ingress after the test to evaluate the fixture's waterproof capability.
Vibration Test Method: Expose the lighting fixture to controlled vibration using a vibration testing machine. Inspect for any mechanical failures or loose components after the test to ensure the fixture's durability and reliability.
Environmental Performance Test Method: Conduct environmental tests, such as temperature and humidity tests, to evaluate the lighting fixture's performance under different environmental conditions. Monitor for any performance degradation or abnormalities.
CNS 9118-2010:道路照明灯具
QB/T 5533-2020:教室照明灯具
JT/T 609-2022:公路隧道照明灯具
JT/T 939.4-2020:公路LED照明灯具 第4部分:桥梁护栏LED照明灯具
JT/T 939.3-2023:公路LED照明灯具 第3部分:公路室外LED照明灯具
JT/T 939.2-2014:公路LED照明灯具 第2部分:公路隧道LED照明灯具
GB/T 3027-2012:船用白炽照明灯具
GB 30734-2014:消防员照明灯具
CNS 15015-2016:户外景观照明灯具
CB/T 3857-2013:船用荧光照明灯具
GB/T 7002-2008:投光照明灯具光度测试
CB 1246-1994:舰船用照明灯具通用规范
GB/T 24827-2015:道路与街路照明灯具性能要求
QB/T 1552-1992:照明灯具反射器油漆涂层技术条件
TB/T 2796-1997:铁路隧道固定式照明灯具技术条件
CNS 9116-1982:家庭用垂吊式荧光管照明灯具
CNS 8802-2007:紧急照明灯
JT/T 939.1-2014:公路LED照明灯具 第1部分:通则
CNS 15233-2012:发光二极管道路照明灯具
JT/T 939.5-2014:公路LED照明灯具 第5部分:照明控制器
QB/T 2054-2008(2017):局部照明灯泡
QB/T 2054-2008:局部照明灯泡
HB 6091-1986:飞机座舱仪表表外照明灯具 通用技术要求
CNS 9117-1982:家庭用垂吊式荧光管照明灯具检验法
GB 7000.2-2008:灯具 第2-22部分:特殊要求 应急照明灯具
GB/T 7000.222-2023:灯具 第2-22部分:特殊要求 应急照明灯具
GB 7000.203-2013:灯具 第2-3部分:特殊要求 道路与街路照明灯具
CJ/T 527-2018:道路照明灯杆技术条件
JG/T 467-2014:建筑室内用发光二极管(LED)照明灯具
CB/T 3852.3-2008:船用照明灯具 类型、参数和主要尺寸 第3部分:投光灯
1.具体的试验周期以工程师告知的为准。
2.文章中的图片或者标准以及具体的试验方案仅供参考,因为每个样品和项目都有所不同,所以最终以工程师告知的为准。
3.关于(样品量)的需求,最好是先咨询我们的工程师确定,避免不必要的样品损失。
4.加急试验周期一般是五个工作日左右,部分样品有所差异
5.如果对于(照明灯具检测)还有什么疑问,可以咨询我们的工程师为您一一解答。
上一篇: 居住、商业和轻工业中的电气和电
下一篇: 中药细菌检测